A great plumbing tip which can save you a lot of money on a daily basis is to invest in a low GPF (gallons per flush) model toilet. As such, every time you flush the toilet you will be using less water than before, and doing so will save you on your water bill.

There are many ways to unclog a drain. You can try plunging it at first. If that doesn’t work try using a chemical agent from the store. Before you go and spend money at the store though, if you have baking soda and some vinegar handy, you can mix those together and pour them in the drain and try to plunge that but if all else fails they have stronger remedies at your local hardware store.

If you have an automatic sprinkler system, you want to consider getting a spring-loaded timer which can be attached directly to your hose. This prevents your lawn from getting too much water in case you forget to turn your system off. Getting too much water could kill your grass and plants.

Is your toilet leaking? Find out by putting some food color in the tank and then check the bowl later. If there is colored water in the bowl, the toilet has an internal leak. To fix an internal leak you can simply replace the tank’s ball or flapper.

If the water in your shower or tub seems cold, even though the water coming out of your kitchen faucet is hot, don’t assume the worst. The faucets in your shower or tub enclosure have been preset to prevent burning and the way this is accomplished it that most newer faucets have a little mechanism in place to prevent turning the handle to the point where you get hot water. You can remove the faucet handle and readjust that mechanism to allow the handle to turn more and get you much hotter water.

When facing temperatures below freezing in the winter it is important to leave the hot water dripping. This makes sure that the pipes don’t freeze over and saves you the expensive repair of fixing and or entirely replacing a broken pipe. The slight cost of dripping hot water is well worth saving you from that large expense of replacing a broken pipe.

A great way to save a few dollars is to add insulation to your hot water heater. Much of the energy required to heat the water in your home is the expense from keeping the water in the tank hot for when it is needed. Adding an extra layer of insulation can help reduce this cost.

If your pipes are making banging noises, you may need to add additional anchor straps to prevent the pipes from making contact with the walls when water is traveling through them. Typically, pipes are anchored at regular intervals. If banging noises are occurring, you may need to add additional straps or cushion the pipes with a rubber blanket.

To help you save money with plumbing, you should perform regular preventative maintenance. Without performing preventative maintenance, your drains will eventually get clogged and you will have to call a plumber. Calling a plumber can be expensive, so in order to avoid these costly repairs, make sure you do regular preventative maintenance.

Speak to a professional before using harsh chemicals to unclog drains or a septic system. Some homes still have very old copper pipes that can be full of rust. While these pipes can still work efficiently, if they are clogged, it is best to use a gentle solution as those harsher chemicals can eat away at the pipe and cause severe issues.

Before you can fix a toilet that does not flush properly, it is important that you find out what is causing the problem. Depending on what the problem is, you may be able to fix it yourself. However, more complicated toilet flushing problems may require the services of a plumber.

Make sure you know where your home’s water shutoff is located. You never know when there might be an emergency involving a broken pipe or damaged connection that requires you to turn off the water right away. In addition, knowing where the shutoff is located is vital before you start any plumbing project, in case anything goes wrong.

Periodically, make sure that the sump pump in your house is working to full capacity. Pour a few gallons of water into the sump pit, and your pump should drain that water out with minimal issues. Checking that your devices are working throughout the year can pay large dividends in the event of a crisis.

Set the temperature on your hot water heater to a temperature that does not exceed 120 degrees. This helps to save energy and prevents the water from becoming too hot and potentially scalding someone in your household. Older models that do not have a temperature setting should be set on Medium.

As you can see, hiring a professional plumber is usually an unnecessary and expensive thing to do, compared to fixing the problem yourself. Next time your plumbing needs repair, try pulling up this article and trying to solve it yourself. You may be surprised how easy it is to do!

Lewis Pocklington produces e-books on plumber Newcastle